Shaft parts are a common type of parts, its structure is a rotating body, the length is generally greater than the diameter, and it is widely used in various mechanical equipment to support transmission parts, transmit torque and bear load. The processing of shaft parts should follow certain rules, and you can learn about the specific processing steps and some problems that need attention through this article.
First, the basic processing route of shaft parts
The main processing surface of shaft parts is the cylindrical surface and the common special surface, so the most suitable processing method should be selected for various accuracy levels and surface roughness requirements. Its basic processing route can be summarized into four.
First of all, it is the processing route from the rough car to the semi-fine car, and then to the fine car, which is also the most important process route selected for the cylindrical processing of shaft parts of commonly used materials; Secondly, it is from the rough car to the semi-fine car, and then to the rough grinding, and finally adopts the fine grinding processing route, which is the best choice for black metal materials and parts with high precision requirements, small surface roughness requirements and need to be hardened, because grinding is the most ideal subsequent processing process; The third route is from rough car to semi-fine car, and then to fine car, diamond car, this processing route is specially used to process non-ferrous metal materials, because non-ferrous metal hardness is small, easy to block the gap between the sand particles, the use of grinding is usually not easy to get the required surface roughness, must use fine car and diamond car process; The last processing route is from rough to semi-finished, and then to rough grinding, fine grinding, and finally finishing, this route is often used for the black metal material after hardening, and the precision requirements are higher, the surface roughness value requirements are low parts.
Second, the preprocessing of shaft parts
Before turning the outer circle of the shaft parts, some preparation processes must be carried out first, which is the pre-processing process of the shaft parts. The most important preparation step is straightening. Because the workpiece blank in the manufacturing, transportation and storage process, often occur bending deformation. In order to ensure reliable clamping and uniform distribution of processing allowance, the straightening is carried out by various presses or straightening machines in cold state.
Third, the positioning basis of shaft parts processing
First of all, the center hole of the workpiece is used as the positioning benchmark for processing. In the processing of shaft parts, the coaxiality of each cylindrical surface, cone hole and thread surface, and the perpendicularity of the end facing the axis of rotation are all important manifestations of position accuracy. These surfaces are generally based on the center line of the shaft as the design basis, with the center hole positioning, in line with the principle of reference coincidence. The center hole is not only the positioning benchmark for turning processing, but also the positioning benchmark and inspection benchmark for other processing processes, which conforms to the principle of unification of the benchmark. When two center holes are used for positioning, it can also maximize the processing of multiple outer circles and end faces in a single clamping.
Secondly, the outer circle and the center hole are used as the positioning basis for processing. This method effectively overcomes the shortcomings of poor rigidity of center hole positioning, especially when processing heavy workpieces, center hole positioning will cause clamping instability, and the cutting amount can not be too large. Using the outer circle and the center hole as the positioning basis does not have to worry about this problem. When roughing, the method using the cylindrical surface of the shaft and a central hole as the positioning reference can withstand large cutting torque in the processing, and is the most common positioning method for shaft parts.
Third, two outer circular surfaces are used as the positioning basis for processing. When machining the inner hole of the hollow shaft, the center hole cannot be used as the positioning reference, so the two outer circular surfaces of the shaft should be used as the positioning reference. When machining the spindle of the machine tool, the two support journals are often used as the positioning reference, which can effectively ensure the coaxiality requirements of the cone hole relative to the support journal and eliminate the error caused by the non-coincidence of the reference.
Finally, a cone plug with a central hole is used as the positioning basis for processing. This method is most commonly used in the machining of the cylindrical surface of the hollow shaft.
Fourth, the clamping of shaft parts
The machining of the cone plug and the cone sleeve mandrel must have a high processing accuracy, and the center hole is not only the positioning benchmark of its own manufacturing, but also the benchmark of the hollow shaft cylindrical finishing, and must ensure that the cone and the center hole on the cone plug or the cone sleeve mandrel have a high coaxiality. Therefore, when selecting the clamping method, attention should be paid to minimizing the number of cone plug installations, so as to reduce the repeated installation error of the parts. In actual production, after the cone plug is installed, it is generally not removed or replaced in the middle of processing before the processing is completed.

